How to Insulate a Garage Door

How to insulate a garage door

If you have a connected garage with an uninsulated garage door, it’s costing you cash in both the winter season and summer. Make sure you have the correct insulation to keep your home efficient.

Research studies done by garage door manufacturers prove that an energy-efficient R-18 insulated garage door can keep your garage about 12 degrees warmer in cold weather and about 25 degrees cooler in summer. That decreases energy loss along the insulated walls and ceiling.

1. Step, mark and install the retainer pins

Procedure to find the area 12 in. from each side of the panel and midway through the horizontal rails. Mark the location. Then remove the adhesive support paper and press the retainer pin base onto the board. Install two retainer pins in each one of the panels.

2. Cut the batting

Roll out the batting with the vinyl side down and make sure to mark the cutting lines. Place the batting on scrap plywood. Then compress the insulated garage door and cut with a utility knife.

3. Lock the batting in location

Line up the insulation so it’s centered in the panel and push it against the keeping pin until it punctures the vinyl dealing. Then press the maintaining cap over the pin till it snaps into location. Start by cleaning each door panel with family cleansing spray and rags. Rinse with clean water and let it dry off. Next, set up the retaining pins. Step the height and width of each panel and include 1 in. to the length and width when you cut the batting to size for a snug fit. Panel sizes may differ along the door, so determine each one as you go instead of pre-cutting all the panels based on one measurement. Fit the cut insulation into the board with the vinyl side dealing into the garage. Then protect it to the keeping pins. Repeat till all the panels are insulated.

4. Test-fit the doorstep

Place the doorstop versus the top and side jambs so the vinyl weather removal is at a 45-degree angle. Briefly protect it in place with nails pounded in only partway.

5. Readjust to accommodate door motion

Apply pressure to the door to simulate the impact of a strong wind. Then move the doorstop inward to keep a great seal. The gap might not be the same in every location along the sides, so inspect it in several areas and adjust accordingly. Starting at the top of the door, tack the doorstop weather removing to the top jamb. Mount the side doorstops the same way. Then press against the door to simulate how much it may move in strong winds. Adjust the doorstop, so it seals versus the door even in windy conditions. Pound the nails all the way in. If the door has too much play to adjust effectively, or you can see the light through the doorstop weather stripping, replace your existing hinges with spring-loaded versions that press the door versus the weather condition stripping at all times. Set up a new bottom seal.

6. Uncrimp the bottom seal track slots

Jam a fat-blade screwdriver into the crimped location and twist to gently bend out the aluminum track. Repeat on each end of the way.

7. Slide in the new bottom seal

Slather dishwashing detergent onto the slots along the bottom track or spray them with silicone. Then insert the vinyl seal and pull it into location. Cut off the excess vinyl with a utility knife and crimp the ends of the track with a set of pliers.  

Many steel doors have a track along the bottom to hold a vinyl seal. The vinyl can harden from direct sun exposure and fracture or break off in sections, letting in cold air. Installers typically crimp the slots at each end of the track to keep the seal. Open the crimps and remove the old seal. Then install the brand-new one. Evaluate the door 

An appropriately well-balanced garage door needs to remain in location if you raise it partway and let go. Nevertheless, insulation adds weight to the door, which might throw off balance. If your door falls after you let go of it, hire a garage door service company to adjust the spring stress. Leaving the door in an out-of-balance state can damage your garage door opener.

More Posts

How to sand drywall

How to sand drywall

The most important task in any home renovation involves drywall. Once you are done hanging drywall sheets, start filling in any gaps or nail gouges

Subscribe to our Newsletter

Want to Save 10% Off Your First Order? Become a Member to Unlock Your Code!

Want to Save 10% Off Your First Order? Become a Member to Unlock Your Code!